



Network Working Group                                        A. Maurette
Internet-Draft                                           IUT R&T Béthune
Intended status: Experimental                            18 January 2026
Expires: 22 July 2026


     HMTFTP: HMAC-Derived TFTP with Optional AEAD Protection (v0.2)
                        draft-maurette-hmtftp-02

Abstract

   HMTFTP is a lightweight UDP file transfer protocol that preserves the
   simplicity of TFTP (block-and-ACK) while adding a structured TLV
   extension mechanism and an optional authenticated-encryption mode.
   When negotiated, DATA payloads are protected with AEAD AES-256-GCM
   and keys are derived with HKDF-SHA-256 from a pre-shared key (PSK).
   The default UDP port is TBD (requested: 6369) and implementations
   MUST allow it to be configured.

Additional Status Note

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."

Status of This Memo

   This Internet-Draft is submitted in full conformance with the
   provisions of BCP 78 and BCP 79.

   Internet-Drafts are working documents of the Internet Engineering
   Task Force (IETF).  Note that other groups may also distribute
   working documents as Internet-Drafts.  The list of current Internet-
   Drafts is at https://datatracker.ietf.org/drafts/current/.

   Internet-Drafts are draft documents valid for a maximum of six months
   and may be updated, replaced, or obsoleted by other documents at any
   time.  It is inappropriate to use Internet-Drafts as reference
   material or to cite them other than as "work in progress."



Maurette                  Expires 22 July 2026                  [Page 1]

Internet-Draft                 HMTFTP v0.2                  January 2026


   This Internet-Draft will expire on 22 July 2026.

Copyright Notice

   Copyright (c) 2026 IETF Trust and the persons identified as the
   document authors.  All rights reserved.

   This document is subject to BCP 78 and the IETF Trust's Legal
   Provisions Relating to IETF Documents (https://trustee.ietf.org/
   license-info) in effect on the date of publication of this document.
   Please review these documents carefully, as they describe your rights
   and restrictions with respect to this document.  Code Components
   extracted from this document must include Revised BSD License text as
   described in Section 4.e of the Trust Legal Provisions and are
   provided without warranty as described in the Revised BSD License.

Table of Contents

   1.  Introduction  . . . . . . . . . . . . . . . . . . . . . . . .   3
   2.  Conventions and Terminology . . . . . . . . . . . . . . . . .   3
   3.  Relationship to TFTP  . . . . . . . . . . . . . . . . . . . .   3
   4.  Transport . . . . . . . . . . . . . . . . . . . . . . . . . .   4
   5.  Message Formats . . . . . . . . . . . . . . . . . . . . . . .   4
     5.1.  RRQ and WRQ . . . . . . . . . . . . . . . . . . . . . . .   4
     5.2.  OACK  . . . . . . . . . . . . . . . . . . . . . . . . . .   4
     5.3.  DATA and ACK  . . . . . . . . . . . . . . . . . . . . . .   4
     5.4.  ERROR . . . . . . . . . . . . . . . . . . . . . . . . . .   5
   6.  TLV Encoding and Processing . . . . . . . . . . . . . . . . .   5
     6.1.  Defined TLVs  . . . . . . . . . . . . . . . . . . . . . .   6
   7.  Transfer Procedure  . . . . . . . . . . . . . . . . . . . . .   8
   8.  Optional AEAD Security Mode . . . . . . . . . . . . . . . . .   8
     8.1.  Negotiation TLVs  . . . . . . . . . . . . . . . . . . . .   8
     8.2.  Key Derivation  . . . . . . . . . . . . . . . . . . . . .   8
     8.3.  Nonce Construction and AAD  . . . . . . . . . . . . . . .   9
     8.4.  Limits  . . . . . . . . . . . . . . . . . . . . . . . . .   9
   9.  Security Considerations . . . . . . . . . . . . . . . . . . .   9
   10. Implementation Status . . . . . . . . . . . . . . . . . . . .  10
   11. References  . . . . . . . . . . . . . . . . . . . . . . . . .  10
     11.1.  Normative References . . . . . . . . . . . . . . . . . .  10
     11.2.  Informative References . . . . . . . . . . . . . . . . .  11
   Author's Address  . . . . . . . . . . . . . . . . . . . . . . . .  11










Maurette                  Expires 22 July 2026                  [Page 2]

Internet-Draft                 HMTFTP v0.2                  January 2026


1.  Introduction

   The Trivial File Transfer Protocol (TFTP) [RFC1350] is extremely
   simple but provides no built-in security properties.  HMTFTP retains
   the TFTP operational model (UDP, numbered blocks, ACKs) while
   introducing (1) a compact TLV extension mechanism and (2) an optional
   AEAD protection mode for DATA payloads.

   The name "HMTFTP" reflects that cryptographic keys are derived using
   HKDF, a HMAC-based key derivation function [RFC5869] .  This version
   (v0.2) focuses on removing specification blockers: well-defined
   extension processing rules and explicit security boundaries (what is
   encrypted vs. authenticated).

2.  Conventions and Terminology

   The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
   "SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
   document are to be interpreted as described in BCP 14 ( [RFC2119] and
   [RFC8174] ) when, and only when, they appear in all capitals.

   This document uses the following terms:

   *  *PSK* : pre-shared key

   *  *AEAD* : authenticated encryption with associated data

   *  *AAD* : additional authenticated data

3.  Relationship to TFTP

   HMTFTP is derived from TFTP [RFC1350] and reuses the core message
   types and semantics (RRQ, WRQ, DATA, ACK, ERROR).  It also reuses the
   concept of an explicit option acknowledgment, OACK, as introduced by
   TFTP option extension [RFC2347] . HMTFTP replaces the key/value
   option encoding of RFC 2347 with a TLV encoding defined in this
   document.

   HMTFTP differs from baseline TFTP primarily by:

   *  using UDP port TBD by default (requested: 6369; configurable),
      rather than 69;

   *  allowing TLV extensions in RRQ, WRQ, and OACK;

   *  supporting an optional AEAD security mode for DATA payloads.





Maurette                  Expires 22 July 2026                  [Page 3]

Internet-Draft                 HMTFTP v0.2                  January 2026


4.  Transport

   HMTFTP runs over UDP.  The default server port is TBD (requested:
   6369), but implementations MUST allow the port to be configured.

   As in TFTP, a transfer is conducted between a client and a server
   transfer address (IP, UDP port).  The server MAY respond from a
   different UDP port than the configured well-known port for the
   remainder of the transfer, as described in [RFC1350] .

5.  Message Formats

   All multi-octet fields are encoded in network byte order (big-
   endian).  HMTFTP reuses the TFTP base message formats, with TLVs
   appended to RRQ, WRQ, and OACK.  TLVs are not used in DATA, ACK, or
   ERROR in v0.2.

5.1.  RRQ and WRQ

   RRQ and WRQ are defined as in [RFC1350] :

   *RRQ/WRQ* = OpCode (2) || Filename (N) || 0 || Mode (M) || 0 ||
   [TLVs]

   The optional TLV sequence, when present, begins immediately after the
   terminating zero octet of the Mode field and continues to the end of
   the UDP datagram.  The Mode is a NUL-terminated ASCII string (e.g.,
   "octet").

5.2.  OACK

   OACK is used by the server to acknowledge and/or modify the TLVs
   offered in RRQ/WRQ.  OACK is defined by [RFC2347] as OpCode value 6.
   In HMTFTP, OACK contains only a TLV sequence:

   *OACK* = OpCode (2) || TLVs

   An OACK with an empty TLV sequence indicates acceptance with no
   negotiated parameters.

5.3.  DATA and ACK

   DATA and ACK are as defined in [RFC1350] :

   *DATA* = OpCode (2) || Block (2) || Payload (0..n)

   *ACK* = OpCode (2) || Block (2)




Maurette                  Expires 22 July 2026                  [Page 4]

Internet-Draft                 HMTFTP v0.2                  January 2026


   When AEAD protection is negotiated ( Section 8 ), the DATA Payload is
   structured as: Ciphertext || Tag, where Tag is a 16-octet AES-GCM
   authentication tag.  The ciphertext length is the datagram length
   minus 4 octets of header and minus 16 octets of tag.

5.4.  ERROR

   ERROR is as defined in [RFC1350] :

   *ERROR* = OpCode (2) || ErrorCode (2) || ErrMsg (string) || 0

   HMTFTP endpoints SHOULD use an ERROR with ErrorCode 0 ("Not defined")
   for extension processing failures (e.g., unsupported critical TLV).

6.  TLV Encoding and Processing

   HMTFTP TLVs extend RRQ, WRQ, and OACK.  TLVs use a compact binary
   encoding:

        +========+==========+====================================+
        | Field  | Size     | Description                        |
        +========+==========+====================================+
        | Type   | 16 bits  | Type code with Critical bit in MSB |
        +--------+----------+------------------------------------+
        | Length | 16 bits  | Length of Value in octets          |
        +--------+----------+------------------------------------+
        | Value  | variable | Type-specific data                 |
        +--------+----------+------------------------------------+

                           Table 1: TLV Format

   The most significant bit (MSB) of the Type field is the _Critical_
   bit.  Bits 0-14 form the 15-bit TLV code.  The Critical bit is not
   part of any future registry code space that may be defined for TLV
   codes.

   Processing rules:

   *  A receiver MUST ignore unknown TLVs with Critical=0.

   *  A receiver that encounters an unknown TLV with Critical=1 MUST
      reject the message by sending an ERROR (and MUST NOT proceed with
      the transfer).

   *  A receiver MAY accept known TLVs in any order.  If a TLV appears
      multiple times, a receiver SHOULD treat this as an error unless
      the TLV definition explicitly allows repetition.




Maurette                  Expires 22 July 2026                  [Page 5]

Internet-Draft                 HMTFTP v0.2                  January 2026


6.1.  Defined TLVs

   This specification defines the following TLVs.  All multi-octet
   values are encoded in network byte order (big-endian).















































Maurette                  Expires 22 July 2026                  [Page 6]

Internet-Draft                 HMTFTP v0.2                  January 2026


   +========+=========+========+======================================+
   | Code   | Name    | Length | Description                          |
   +========+=========+========+======================================+
   | 0x0001 | BLKSIZE | 2      | Requested maximum DATA payload size  |
   |        |         |        | in octets (uint16).  If offered by a |
   |        |         |        | client, the server MUST respond with |
   |        |         |        | BLKSIZE in OACK with the selected    |
   |        |         |        | value, which MUST be less than or    |
   |        |         |        | equal to the requested value.        |
   +--------+---------+--------+--------------------------------------+
   | 0x0002 | TIMEOUT | 2      | Requested retransmission timeout in  |
   |        |         |        | seconds (uint16).  If offered by a   |
   |        |         |        | client, the server MUST respond with |
   |        |         |        | TIMEOUT in OACK with the selected    |
   |        |         |        | value (which MAY be less than the    |
   |        |         |        | requested value) or reject the       |
   |        |         |        | request.                             |
   +--------+---------+--------+--------------------------------------+
   | 0x0003 | TSIZE   | 8      | Transfer size in octets (uint64).    |
   |        |         |        | In RRQ, a client MAY send TSIZE=0 to |
   |        |         |        | request that the server return the   |
   |        |         |        | size.  In WRQ, a client SHOULD send  |
   |        |         |        | TSIZE with the size if known.        |
   +--------+---------+--------+--------------------------------------+
   | 0x0010 | ENC_REQ | 0      | Request to enable AEAD protection    |
   |        |         |        | for DATA payloads.  Clients that     |
   |        |         |        | require security mode MUST set the   |
   |        |         |        | Critical bit on ENC_REQ.  Servers    |
   |        |         |        | that accept security mode MUST echo  |
   |        |         |        | ENC_REQ in OACK.                     |
   +--------+---------+--------+--------------------------------------+
   | 0x0011 | CIPHER  | 2      | Select ciphersuite (uint16).  If     |
   |        |         |        | omitted, the default ciphersuite is  |
   |        |         |        | 0x0001 (AES-256-GCM).                |
   +--------+---------+--------+--------------------------------------+
   | 0x0012 | CNONCE  | 16     | Client nonce (16 octets) generated   |
   |        |         |        | by a CSPRNG.  CNONCE MUST be present |
   |        |         |        | in RRQ/WRQ when ENC_REQ is present.  |
   +--------+---------+--------+--------------------------------------+
   | 0x0013 | SNONCE  | 16     | Server nonce (16 octets) generated   |
   |        |         |        | by a CSPRNG.  SNONCE MUST be present |
   |        |         |        | in OACK when ENC_REQ is accepted.    |
   +--------+---------+--------+--------------------------------------+

                       Table 2: Defined TLVs (v0.2)

   The ciphersuite value 0x0001 corresponds to AEAD AES-256-GCM.




Maurette                  Expires 22 July 2026                  [Page 7]

Internet-Draft                 HMTFTP v0.2                  January 2026


7.  Transfer Procedure

   HMTFTP uses the following procedure, aligned with TFTP option
   negotiation [RFC2347] :

   1.  The client sends RRQ or WRQ, optionally with TLVs.

   2.  If the server accepts the request and any offered parameters, it
       replies with OACK containing the negotiated TLVs (which MAY be
       empty).  If the server does not support a critical TLV or rejects
       parameters, it replies with ERROR.

   3.  For RRQ: the client sends ACK(0) after receiving OACK, then the
       server starts with DATA(1).

   4.  For WRQ: the client starts with DATA(1) after receiving OACK, and
       the server acknowledges each block with ACK(n).

   Apart from the OACK exchange, block numbering, retransmissions, and
   EOF signaling follow [RFC1350] .

8.  Optional AEAD Security Mode

   Security mode is negotiated using TLVs in RRQ/WRQ and OACK.  When
   enabled, each DATA payload is protected with AEAD AES-256-GCM
   [RFC5116] .  The AEAD key and IV base are derived using HKDF-SHA-256
   [RFC5869] .

8.1.  Negotiation TLVs

   The client requests security mode by including TLV ENC_REQ in RRQ/
   WRQ.  When ENC_REQ is present, the client MUST include CNONCE and MAY
   include CIPHER.  If the server accepts, it includes ENC_REQ and
   SNONCE in OACK and MAY include (or echo) CIPHER.  If the server does
   not support security mode, it MUST reject a Critical ENC_REQ with
   ERROR.

8.2.  Key Derivation

   This document assumes an externally provisioned PSK (32 octets
   RECOMMENDED).  During negotiation, the client and server exchange
   nonces: CNONCE and SNONCE, each 16 octets from a CSPRNG.

   The AEAD key material is derived as follows:

   *  IKM = PSK

   *  salt = CNONCE || SNONCE (32 octets)



Maurette                  Expires 22 July 2026                  [Page 8]

Internet-Draft                 HMTFTP v0.2                  January 2026


   *  info = "hmtftp v0.2 keys"

   *  OKM = HKDF-SHA-256(IKM, salt, info, 44)

   *  key = OKM[0..31] (32 octets)

   *  iv_base = OKM[32..43] (12 octets)

8.3.  Nonce Construction and AAD

   The AES-GCM nonce (12 octets) for DATA block number _n_ is:

   nonce = iv_base[0..7] || uint32(n)

   where uint32(n) is the 32-bit big-endian encoding of the DATA block
   number (n is the 16-bit Block field widened to 32 bits).

   The AEAD AAD is the 4-octet DATA header (OpCode || Block).  RRQ/WRQ/
   OACK metadata and TLVs are not encrypted and are not included in the
   DATA AAD in v0.2.

   Retransmissions MUST retransmit the exact same ciphertext and tag for
   a given block number (key, nonce).

8.4.  Limits

   To avoid nonce reuse, endpoints MUST NOT allow the 16-bit block
   number to wrap within a security context.  Implementations SHOULD
   terminate a transfer with ERROR well before wrap if it would be
   reached.

9.  Security Considerations

   Without security mode, HMTFTP provides no confidentiality or
   integrity beyond UDP checksums and is vulnerable to on-path
   modification and spoofing, as with TFTP [RFC1350] .

   With security mode enabled, only DATA payloads are encrypted and
   authenticated.  RRQ/WRQ/OACK metadata and TLVs remain in cleartext.
   This means filenames, modes, and negotiated parameters are observable
   on the wire.  Deployments that require metadata confidentiality MUST
   avoid placing sensitive data in RRQ/WRQ/OACK and SHOULD use an
   external secure channel or a future extension that encrypts metadata.

   Nonce reuse with AES-GCM is catastrophic.  Implementations MUST
   enforce nonce uniqueness and MUST follow the nonce construction and
   wrap limits described in Section 8 .




Maurette                  Expires 22 July 2026                  [Page 9]

Internet-Draft                 HMTFTP v0.2                  January 2026


   Implementations should also consider UDP robustness guidelines (
   [RFC8085] ) and rate-limiting to mitigate amplification and resource-
   exhaustion attacks.

10.  Implementation Status

   This section is provided for RFC 7942 compliance ( [RFC7942] ).
   Implementations, interop notes, and known limitations will be added
   in subsequent versions.

11.  References

11.1.  Normative References

   [RFC1350]  Sollins, K., "The TFTP Protocol (Revision 2)", RFC 1350,
              July 1992, <https://www.rfc-editor.org/rfc/rfc1350>.

   [RFC2119]  Bradner, S., "Key words for use in RFCs to Indicate
              Requirement Levels", BCP 14, RFC 2119, March 1997,
              <https://www.rfc-editor.org/rfc/rfc2119>.

   [RFC8174]  Leiba, B., "Ambiguity of Uppercase vs Lowercase in RFC
              2119 Key Words", BCP 14, RFC 8174, May 2017,
              <https://www.rfc-editor.org/rfc/rfc8174>.

   [RFC2347]  Malkin, G., "TFTP Option Extension", RFC 2347, May 1998,
              <https://www.rfc-editor.org/rfc/rfc2347>.

   [RFC2348]  Malkin, G., "TFTP Blocksize Option", RFC 2348, May 1998,
              <https://www.rfc-editor.org/rfc/rfc2348>.

   [RFC2349]  Malkin, G., "TFTP Timeout Interval and Transfer Size
              Options", RFC 2349, May 1998,
              <https://www.rfc-editor.org/rfc/rfc2349>.

   [RFC5116]  McGrew, D., "An Interface and Algorithms for Authenticated
              Encryption", RFC 5116, January 2008,
              <https://www.rfc-editor.org/rfc/rfc5116>.

   [RFC5869]  Krawczyk, H. and P. Eronen, "HMAC-based Extract-and-Expand
              Key Derivation Function (HKDF)", RFC 5869, May 2010,
              <https://www.rfc-editor.org/rfc/rfc5869>.

   [RFC6335]  Cotton, M., Leiba, B., and T. Narten, "Internet Assigned
              Numbers Authority (IANA) Procedures for the Management of
              the Service Name and Transport Protocol Port Number
              Registry", RFC 6335, August 2011,
              <https://www.rfc-editor.org/rfc/rfc6335>.



Maurette                  Expires 22 July 2026                 [Page 10]

Internet-Draft                 HMTFTP v0.2                  January 2026


   [RFC8085]  Eggert, L., Fairhurst, G., and G. Shepherd, "UDP Usage
              Guidelines", RFC 8085, March 2017,
              <https://www.rfc-editor.org/rfc/rfc8085>.

   [RFC8126]  Cotton, M., Leiba, B., and T. Narten, "Guidelines for
              Writing an IANA Considerations Section in RFCs", BCP 26,
              RFC 8126, June 2017,
              <https://www.rfc-editor.org/rfc/rfc8126>.

11.2.  Informative References

   [RFC7942]  Bormann, C., "Improving Awareness of Running Code: The
              Implementation Status Section", RFC 7942, July 2016,
              <https://www.rfc-editor.org/rfc/rfc7942>.

Author's Address

   A. Maurette
   IUT R&T Béthune
   France
   Email: contact@c4tz.fr






























Maurette                  Expires 22 July 2026                 [Page 11]
